Home › Resource Center › Logbooks and maintenance records

Engine times explained: total time, SMOH and TBO

Updated November 19, 2026 · About an 8-minute read

"1,450 SMOH, 4,200 TT, 2,000 TBO." Engine times drive an airplane's value and its maintenance plan, and the terms get used loosely. Here's what each one means, what the FAA rules say, and where the engine makers publish their overhaul recommendations, with the source for each point at the bottom.

For piston engines on type-certificated aircraft operated under Part 91. Commercial operations can have different requirements. Not legal advice.

Time in service: what the hours are

  • For maintenance records, the FAA defines time in service as the time from the moment an aircraft leaves the surface of the earth until it touches it at the next point of landing (14 CFR 1.1).
  • Time-recording devices sense things like electrical power, oil pressure or the wheels being on the ground, so except for those that sense lift-off and touchdown, their readings are approximate. FAA guidance says they're very helpful for arriving at time in service, but the instruments alone don't meet the record-keeping rule (AC 43-9D).
  • Lycoming says engine hours should be recorded using the same method the airframe manufacturer or operator chose for time in service (SI 1009). Continental doesn't specify a method and defers to the installer (SIL98-9).
  • If a tach or Hobbs is replaced, the records need the time in service and the reading at the change, or continuity is lost (AC 43-9D).

The terms

  • Total time (TT, or TTSN, "since new"): all the time in service the engine has ever accumulated. The owner's records must show the total time in service of the airframe, each engine and each propeller (14 CFR 91.417(a)(2)(i)). Total time keeps counting through overhauls.
  • Time since overhaul (often written SMOH, "since major overhaul"): the hours since the engine was last overhauled. "Major overhaul" is industry shorthand; the FAA's rules just say "overhaul."
  • Overhauled: a required entry may call an engine overhauled only if, using methods acceptable to the FAA, it was disassembled, cleaned, inspected, repaired as necessary and reassembled, and then tested to approved standards and technical data, or to current standards and data acceptable to the FAA from the type certificate, STC or parts-approval holder (14 CFR 43.2(a)).
  • Rebuilt: a stricter term. It may be used only if the engine was disassembled, cleaned, inspected, repaired as necessary, reassembled, and tested to the same tolerances and limits as a new item, using new parts or used parts that meet new-part limits or approved oversize or undersize dimensions (43.2(b)).
  • Zero time: only an engine rebuilt by its manufacturer, or an agency the manufacturer approves, may start a new maintenance record without its previous operating history. The rebuilder enters a signed statement of the rebuild date and each change made for ADs and, where requested, service bulletins (14 CFR 91.421). That is the one case where total time starts over.
  • Other labels: FAA guidance warns that when terms like "remanufactured" or "reconditioned" appear in records, owners can't assume the work required to call something "rebuilt" was done (AC 43-9D).

TBO: time between overhauls

TBO is the engine manufacturer's overhaul interval, given in operating hours and in calendar years, whichever comes first. Look up your exact engine model in the manufacturer's current document:

  • Lycoming: Service Instruction 1009, "Time Between Overhaul (TBO) Schedules." The current revision, 1009BF dated July 20, 2026, says all engine models are to be overhauled within 12 calendar years of first entering service or of last overhaul, and lists operating-hour TBOs by model, with separate figures for an engine's first run after delivery as factory new or factory rebuilt and for engines after any overhaul. The 2026 revision changed the hours for some models, so check the current table and its notes. Lycoming says its TBOs apply only to engines kept to its conditions (original type certificate configuration, genuine Lycoming parts or parts identified in the type certificate data sheet or Lycoming service documents, Lycoming-approved procedures, and operation within its specifications). Engines affected by AD 2012-19-01 and not yet in compliance use the TBOs in Lycoming SI 1596 instead.
  • Continental: Service Information Letter SIL98-9, "Time Between Overhaul (TBO) Periods." Revision E (August 20, 2015), the latest we found, lists hours and years by model (12 years for the models in its table), adds 200 hours for an engine that consistently accumulates 40 or more hours a month since being placed in service, and shows higher figures for engines with serial number 1006000 and up. It also says Continental provides no TBO for engines assembled with parts not supplied by Continental, modified from the type certificate configuration, or overhauled outside its instructions. Check Continental for a newer revision.

Both manufacturers say their figures assume the engine is operated and maintained by their instructions, and that individual engines may need overhaul sooner.

Is TBO mandatory?

Asked about a turbine engine's TBO in 2019, the FAA's Office of the Chief Counsel said that following a manufacturer's recommended TBO is not mandatory for an aircraft operated under Part 91, unless the TBO is specified in the FAA-approved Airworthiness Limitations section or required by an AD or other FAA regulation. It added that following it may be good practice (legal interpretation, March 7, 2019). Anything that is in an Airworthiness Limitations section is mandatory (14 CFR 91.403(c)).

Past TBO or not, the engine must be airworthy every time the airplane flies (14 CFR 91.7(a)), and at each annual or 100-hour inspection the inspector runs it to check power, magnetos, pressures and temperatures before approving the aircraft for return to service (14 CFR 43.15(c)(2)).

Don't forget the prop and accessories

Propellers and engine accessories can need overhaul on their own manufacturers' schedules, sometimes before the engine (Lycoming SI 1009). Continental's letter says engine-mounted components and accessories follow the engine's hourly and calendar intervals unless their own manufacturer says otherwise (SIL98-9). Track each one separately.

How GALogbook helps

  • The history behind the numbers: scan the engine and prop logbooks, then ask "When was the engine last overhauled, and by whom?" and see the entry it came from.
  • The whole airplane in one place: airframe, engine and prop logbooks, ADs, 337s, oil records and analysis, and what's coming due.
Know your engine's story. Start the 7-day free trial and scan the engine logbook first.

Get started →   Pre-buy logbook review →

Sources